Stainless Steel Pipe Supplier In India

ASTM A312 Stainless Steel Seamless Pipe Supplier , SA312 Stainless Steel Welded Pipe Manufacturer in India

SS ERW Pipe Exporter In India, Stockist Of ASME SA312 High Pressure Pipes Stock


Stainless Steel Pipe
Stainless Steel Pipe
Stainless Steel Welded Pipe
Stainless Steel Welded Pipe
Stainless Steel Seamless Pipe
Stainless Steel Seamless Pipe

Stainless Steel Pipe & SS different grade

TYPE 317L

  • An austenitic chromium-nickel molybdenum stainless steel
  • Used in Chemical, petroleum, pulp and paper industries
  • Improved chloride pitting resistance over Type 316

TYPE 347 / 347H

  • An austenitic stainless that contains columbium stabilizing elements
  • Excellent for high temperature service in carbide precipitation range
  • Improved intergranular corrosion resistance

TYPE 304H STAINLESS PIPE

  • Used in high temperature over 1000 degrees F
  • Corrosion resistance same as Type 304
  • Higher carbon than Type 304 for better high temperature creep properties

DUPLEX 2205

  • Dual-phase, 45% ferritic and 55% austenitic stainless steel
  • Resists chloride stress corrosion cracking
  • Good strength, toughness and corrosion resistance

TYPE 304 / 304L STAINLESS PIPE

  • An austenitic chromium-nickel stainless steel
  • Non-magnetic except when cold worked
  • General purpose corrosion resistance

254 SMO

  • High resistance to pitting and crevice and general corrosion
  • An austenitic stainless steel with a high Molybdenum content
  • Very high resistance to chloride stress corrosion cracking

TYPE 316 / 316L

  • Improved corrosion resistance to chlorides
  • An austenitic chromium-nickel stainless steel
  • Improved corrosion and heat resistance

TYPE 309S

  • Good for continuous exposure to 2000 degrees F
  • Superior heat resisting austenitic stainless steel
  • Slightly better corrosion resistance than Type 304

904L

  • An austenitic stainless steel with low carbon content
  • Resistance to general corrosion in reducing acids
  • Good resistance to pitting and crevice corrosion

TYPE 410

  • Fair resistance to general corrosion and oxidation
  • Resist abrasion and wear better than most 300 series stainless steel
  • An martensitic stainless steel with high mechanical properties

TYPE 321 / 321H

  • Excellent for high temperature service in carbide precipitation range
  • An austenitic stainless steel that contains titanium stabilizing elements
  • Improved intergranular corrosion resistance

TYPE 446

  • Commonly used in high temperature applications
  • An high chromium ferritic stainless steel
  • Excellent high temperature resistance to oxidation and corrosion

TYPE 310S

  • General corrosion resistance better than Type 304 and 309
  • Superior heat resisting austenitic stainless steel
  • Good for continuous exposure to 2100 degrees F


FASTWELL is a recognized stockholder and exporter of Leak Proof Stainless Steel Pipe & Stainless Steel ERW Pipe in various grades and varying purposes. We always bound to maintain good relationship with our client in overseas buyer, we are able to source material from different countries and supply the same to our overseas customers. We provide special price list on SS Seamless Pipe. We can supply all types of ASTM A213 & A312 SS steel pipes in any region of India and other asian countries and also worldwide. Place your order now and ask us your queries on helpline number or mail on the provided email id. We are determined to comply with the quality standards and timely delivery of our products. All Products from our inventory are available at www.fastwell.in. Our all lines of products have excellent features to offer such as resistance to tarnishing, Robust construction, Compact design, Corrosion-resistance, and more. In tune with industry quality standard, excellent features to offer such as Sturdy construction, Accurate dimensions, Longer service life, and more. FASTWELL is a stockist of high quality SS Welded Pipes & ASTM A358 SS EFW Pipes modern technology.

Pipe Price

SS ERW/Welded Pipe Price Per Kg in India
SS Seamless Pipe Price Per Kg in India
SS Seamless Pipe Price Per Kg in India
SS ERW/Welded Pipe Price Per Kg in India
SS EFW Pipe Price Per Kg in India
SS EFW Pipe Price Per Kg in India

Click here for complete (grade & size wise)

Specification

SS Pipe Specification ASME SA312 / ASTM A358, ASTM A312, ASME SA358
Origin Korean , European, Japanese, US, Russian,Indian (Strictly No Chinese Material)
Pipes Finish Polished ,AP (Annealed & Pickled),BA (Bright & Annealed), MF
Pipes Schedule SCH5, SCH10, SCH40, STD, SCH80, SCH160
SS Seamless Pipe size 4 to 219mm W. T.: 0.5 to 20mm
SS Pipes End Beveled End,Plain End, Treaded.
SS EFW Pipe size 5.0 mm – 1219.2 mm
Round Pipe Regular Stock 16, 17, 18, 19, 20, 21, 22, 23, 25, 28, 31.8, 35, 36, 38.1, 48, 50.8, 60, 63.5, 76.2, 89, 101, 114 mm
Square Pipe Regular Stock 17, 18, 19, 20, 21, 22, 23, 24, 25, 28, 30, 36, 38, 50 mm
Material Test Certificates (MTC) Material Test Certificates (MTC) as per EN 10204/ 3.1B and EN 10204 3.2
Thickness exact 0.25, 0.28, 0.32, 0.37, 0.41, 0.51, 0.61, 0.71, 0.91, 1.11, 1.15, 1.41 mm
Welded Pipe size 5.0 mm – 1219.2 mm
Pipes Form Rectangular, Round, Hydraulic , Straight Pipes , Square, Hollow Etc.
Test
  • Hardness Test
  • Flaring Test
  • Intergranular Corrosion (IGC) Test
  • Flattening Test
  • Pitting Resistance Test
  • Mechanical Testing Such as Tensile of Area
  • Chemical Analysis – Spectro Analysis
  • Micro and MacroTest
  • Positive Material Identification – PMI Testing
Pipes Length Double Random & Cut Length, Single Random.
Rectangle Pipe Regular Stock 10*30, 10*40, 10*50, 20*10, 23*11, 24*12, 25*13, 28*25, 28*13, 29*14, 30*15, 30*20, 30*22, 34*22, 36*23, 50*25, 60*30, 75*45, 95*45 mm
Specialized in Large Diameter SS Pipe
Marking All stainless steel Pipes are marked as follows: Grade,Standard, OD, Length , Thickness , Heat No. (Or according to the customer’s request.)

Types Wall thickness Out diameter Length
Stainless Steel Welded Pipe (in Stock + Custom Sizes) 1.0 ~ 15.0 mm 5.0mm ~ 1219.2mm Upto 6 Meters
Stainless Steel Seamless Pipe (Custom Sizes) As per requirement 5.0mm ~ 203.2mm Upto 6 Meters
NB Sizes (in stock) SCH 5 / SCH 10 / SCH 40 / SCH 80 / SCH 160 1/8” ~ 8” Upto 6 Meters

Stainless Steel Pipe suppliers


ASTM A312 Square Pipe
ASTM A312 Square Pipes
ASME SA312 Weld Pipe
ASME SA312 Weld Pipes
Hollow Pipe
Hollow Pipes
Flex Pipe
Flex Pipes
Exhaust Pipe
Exhaust Pipes
Seamless Pipe
Seamless Pipes
Rectangle Pipe
Rectangle Pipes
Pipe material
Pipes material
ERW Pipe
ERW Pipes
ASTM A358 Welded Pipe
ASTM A358 Welded Pipes
Square Pipe (Radius Corners)
Square Pipes (Radius Corners)
ASTM A312 Clad Pipe
ASTM A312 Clad Pipes
Types of Stainless Steel Seamless & Welded Pipe
  • SS Decorative Pipes
  • Stainless Steel Round Pipe
  • SS Bush Hex Pipes
  • Stainless Steel Hollow Pipes Price
  • stainless steel Round Pipes
  • Stainless Steel Custom Pipes
  • Stainless Steel Round Pipes Price
  • Stainless Steel Thick Wall Pipe
  • SS welded pipe
  • SS Polished Pipes
  • SS lined pipe
  • SCH40 Stainless Steel Pipes
  • Stainless steel electropolished pipe
  • SS Seamless Pipes
  • stainless steel Thin Wall Pipe
  • Stainless Steel Thin Wall Pipe
  • Stainless Steel Thin Wall Pipe
  • SS Thick Wall Pipes
  • Stainless Steel Custom Pipe
  • SS Welded Pipe stockist
  • stainless steel Thick Wall Pipes
  • Stainless Steel Round Pipe
  • SS Custom Pipes
  • Stainless Steel Seamless Pipe
  • Stainless Steel clad pipe
  • SS flex Pipes supplier

SPEC. NO. TITLE SCOPE
AMS 5572
 Steel Tubing, Seamless Corrosion and Heat Resistant 25 Cr; 20 Ni (SAE 30310). Annealed Structural. Parts and assemblies requiring both corrosion and heat resistance especially when welded during fabrication. Requiring oxidation resistance up to approximately 2000°F., but useful at that temperature only when stresses are low.
AMS 5571
 Steel Tubing, Seamless Corrosion andHeai Resistant 18 Cr; 11 Ni; (Cb + Ta)‹SAE 30347). Annealed Structural. Parts and assemblies requiring both corrosion and heat resistance especially when such parts are welded during fabrication. Requiring oxidation resistance up to approximately 1500°F., but useful at that temperature only when stresses are low.
ASTM A 270
 Seamless and Welded Austenitic Stainless Steel Sanitary Tubing. Austenitic stainless steel   intended for usein the diary and food industry in sizes up”to andincluding 4 in. in outside diameter.
AMS 5574
 Seamless Type 309S
Annealed Structural.		 Parts & assemblies requiring both cofrosion and heat resistance up to 2000°F., especially welded assemblies.
ASTM A 268
ASME SA 268
 Seamless and Welded Ferritic Stain-less Steel Tubing for General Service. 15 grades of ferritic stainless steel tubing for general corrosion resistance and high temperature service. (Types 329, 405, 409, 410, 429, 430, 430Ti, 443, 446, XMs & others).
AMS 5565
 Steel Tubing, Welded, Corrosion Resistant 19 Cr; 9 Ni (SAE 30304). Annealed type 304 aircraft hydraulic line tubing. (Not subject to high pressure). Structural.
MIL-T-8504 (T 304)
 Tubing, Steel, Corrosion Resistant 18-8) Annealed, Aircraft Hydraulic Seamless, Welded. Intended for use in high pressure hydraulic and pneumatic systems in which corrosion resistant materials are required. This tubing is of lower strength and higher ductility than tubin Speci- fication MIL-T-6845. May be used to MIL-T-6845 tubing but heavier wall thicknesses must be used. Same qualifications regarding welding, brazing & temperature.
MIL-T-6737 (T 321)
 Tubing, Steel, Corrosion and Heat Resistant (18-8 Stabilized), Welded. Annealed. Type 321 and 347 tubing intended  use in the manufacture of exhaust stacks, manifolds, blast tubes, ring collector and similar applications where a weldable corrosion and heat resisting steel is required or for use at 800º – 1500°F.
ASTM A 358
ASME SA 358
 Electric-Fusion-Welded Austenitic Chromium-Nickel Altoel for High-Temperature For corrosion and high temperature service, normally not less than 8 in. nominal diameter. Types 304, 316, 309, 310, 321, 321, 347, 304L; 316L, 304H, 316H.
ASTM A 376
ASME SA 376
 Seamless Austenitic Pipe for High-Temp Central-Station Service. Austenitic Pipes intended for high temperature and general corrosive service. Better surface than A312 pipe.
ASTM A 409
ASME SA 409
 Welded Large Outside Diameter Light- Wall Austenitic Chromium-Nickel .Alloy Steel Pipe for Corrosive or High-Temperature Service. Nominal diameter 14-30 in. in Schedules SS and 105. Types 304, 309, 310, 316, 317, 321, 347, 348, 304L, 316L.
ASTM A 213

ASME SA 213 		Seamless Ferritic Stainless Steel and Austenitic Stainless Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes. Pressure tubes, made from 16 grades of austenitic stainless steel and from 12 grades of ferritic Cr-Mo Alloy Steel.
AMS 5561
 Steel Tubing, Welded and DrawnHigh Pressure Hydraulic. For parts and assemblies such as fluid lines subject to high pressure and requiring corrosion
ASTM A 530
ASME SA 530
 General Requirements for Carbon, Ferritic Alloy, and Austenitic Alloy Steel Pipe. Common requirements for ASTM pipe specifications as listed.
ASTM A 511
 Seamless Pipes Mechanical Tubing. 27 grades are covered for mechanical applications. Primarily round tubing.
ASTM A 632
 Seamless and Welded Austenitic Tubing for General Service. Small Diameter. 9 grades of austenitic tubing for general corrosion-resisting and high-temperature service.
AMS 5567
 Steel Tubing, Seamless or Welded Corrosion Resistant 19 Cr; 10 Ni (SAE 30304) Hydraulic, Solution Treated. Fluid lines subject to medium high pressures requiring corrosion resistance. Annealed.(1) Seamless    (2) Welded & Drawn
AMS 5557
 Steel Tubing, Corrosion and Heat Resistant 18 Cr; 11 Ni; Ti (SAE30321) Hydraulic. Annealed type 347 hydraulic line tubing.
Type 1—Seamless
Type 2—Welded & Drawn
AMS 5558
 Steel Tubing, Welded, Corrosion and Heat Resistant 18 Cr; 11 Ni, (Cb + Ta) (SAE 30348) Thin Wall. High pressure ducting, wall thickness  or less. Weld bEAD controlled, X-ray.
AMS 5576
 Steel Tubing, Welded, Corrosion and Heat Resistant 18 Cr; 10 Ni; Ti (SAE 30321). Annealed Structural. Parts and assemblies requiring both corrosion and heat resistance especially when such parts are welded during fabrication. Requiring oxidation resistance up to approximately 1500°F., but useful at that temperature only when stresses are low.
MIL-T-5695
 Tubing, Steel, Corrosion Resistant(304),Cold Drawn (1/2 or 1/4 hard Smls or W & D.  Intended for use in fabrication of aircraft structural part requiring a high fegree of resisitance to corrosion.
MIL-T-8808
(T 321)
(T 347)
 Tubing, Steel, Corrosion Resistant (18-8 Stabilized), Aircraft Hydraulic Quality. Annealed. Seamless, Welded & Drawn. Intended for use in high hydraulic and pneumatic systems where and heat resistance are required and in which welding or brazing may be involved during fabrication. Resists oxidation at temperatures to 1200°F., but is useful at that temperature only when stresses are low.
AMS 5560
 Steel Tubing, Seamless CorrosionResistant 19 Cr; 9 Ni (SAE 30304). Annealed type 304 aircraft hydraulic line tubing. (Not subject to high pressure). Structural.
AMS 556
 Steel Tubing, Corrosion and Heat Resistant 18 Cr; 11 Ni; (Cb + Ta) (SAE 30347) Hydraulic. Annealed type 347 hydraulic Iin6 tubing.
Type 1—Seamless
Type 2—Welded & Drawn
AMS 5647
 Seamless Type 304L Cold Finished Mechanical Tube
Rockwell 90B maxHardness
Corrosion Embrittlement Capability
ASTM A 249
ASME SA 249
 Welded Austenitic  Stainless Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes. Pressure tubes, made from austenitic stainless steels, (Types 304, 304H, 304L, 305, 309, 310,316, 316H, 316L, 317, 321, 321H, 347, 347H, 348, 348H, and XM grades.)
MIL-T-8506 (T 304)
 Tubing, Steel, Corrosion Resistant (304) Annealed. Seamless, Welded. Intended for use in the fabrication of aircraft parts requiring a high degree of resistance to corrosion. Not to be used in high pressure hydraulic control systems.
MIL-T-8606
(T 304L)
(T 321)
(T 347)
 Tubin , steel, Corrosion Resistant 18-8 Annealed. Welded & Drawn. Intended for use in applications which require a high degree of resistance to corrosion or to temperatures in the range of 800°F.—1500°F., or in applications which involve welding. Suitable for use In tank-automotive equipment for hydraulic and mechanical applications.
ASTM A 554
 Welded Pipes MechanicalTubing. Nineteen grades are covered for mechanical applications. Rounds, squares, rectangles, and special shapes are included.
AMS 5570
 Steel Tubing, Seamless Corrosion and Heat Resistant 18 Cr; 10 Ni; Ti tSAE 30321). Annealed Structural. Parts and assemblies requiring both corrosion and heat resistance especially when such partsare welded during fabrication. Requiring oxidation resistance up to approximately 1500°F., but useful at that temperature only when stresses are low.
MIL-T-8973
(T304L)
(T 316L)
(T 321)
(T 347)
 Tubing, Steel, Corrosion Resistant, Aerospace Vehicle Hydraulic System. ³/ Hard. Seamless, Welded & Drawn. Intended for use in high pressure hydraulic and pneumatic systems corrosion and heat resistance are required and in which welding or brazing may be involved during fabrication. Suitable for use in temperatures to 1200°F., when stresses are low.
AMS 5562
 Steel Tubing, Seamless Corrosion Resistant 21 Cr; 6 Ni; 9 Mn Annealed. Parts and assemblies requiring both corrosion and heat resistance, and having higher strength than 18-8 types.
AMS 5646
 Seamless Type 347 Cold Finished Mechanical Tube
Rockwell 90B max Hardness
Corrosion Embrittlement Capability
AMS 5573
 Seamless Type 316
Annealed Structural.		 Parts & assemblies requiring both corrosion and heat resistance up to 1600ºF.
ASTM A 450
ASME SA 450
 General Requirements for Alloy Steel Tubes. Common requirements for ASTM tubular specifications.
ASTM A 269
 Seamless and Welded Austenitic Stainless Steel Tubing for General Service. 13 grades of austenitic stainless,steel tubing for general corrosion- resisting and high-temperature service. (Types 304, 304L, 316, 316L, 317, 321,347, 348 and XM grades).
A EBS 5577
 Steel Tubing, Welded, Corrosion and Heat Resistant 25 Cr; 20 Ni; (SAE 30310). Annealed Structural. Parts and assemblies requiring both corrosion and heat resistance especially when welded during fabrication. Requiring oxidation resistance up to approximately 2000°F., but useful at that temperature only when stresses are low.
AMS 5639
 Seamless Type 304 Cold Finished Mechanical Tube
Rockwell 90B max Hardness Corrosion Embrittlement Capability
AMS 5645
 Seamless Type 321 Cold Finished Mechanical Tube
Rockwell 90B max Hardness
Corrosion Embrittlement Capability
ASTM A312
ASME SA 312
 Seamless and Welded Austenitic Pipes. Austenitic intended for high temperature and general corrosive service.22 grades are covered.
AMS 5648
 Seamless Type 316 Cold Finished Mechanical Tube
Rockwell 90B max Hardness
AMS 5566
 Steel Tubing, Seamless or Welded Corrosion Resistant 19 Cr; 10 Ni (SAE 30304) High Pressure Hydraulic. Cold drawn type 304, high pressure, aircraftType 1  SeamlessType 2—Welded Drawn
AMS 5575
 Steel Tubing, Seamless Corrosion and Heat Resistant 16 Cr; 11 Ni; (Cb + Ta) (SAE 30347). Annealed Structural. Parts and assemblies requiring both corrosion and heat resistance espec[ially when such parts are welded during fabrication. Requiring oxidation resistance up to approximately 1500ºF., but useful at that temperature only when stresses are low.
MIL-T-6845 (T 304)
 Tubing, Steel, Corrosion Resistant 304) Aerospace Vehicle Hydraulic ³/ Hard, Seamless, Weldsd Drawn. Intended for use in high pressdre hydraulic and pneumatic systems in which corrosion resistant materials are required. The tubing is not suitable for use in applications assembled by weldin  or brazing or exposed to temperatures higher 800°F.,  because of  impaired  resistance to corrosion, where subsequent anneal not possible.
MIL-P-1144
(T 304) (T 304L)
(T 316) (T 316L)
(T-321) (T 347)
 Pipes, Stainless Steel, (Corrosion Resisting). Seamless or Welded. Annealed. Pipe is intended for high-temperature and hy- draulic or other pressure service under general corrosive conditions.
AMS 5559
 Steel Tubing, Welded, Corrosion and Heat Resistant 18 Cr, 10 Ni, Ti, (SAE 30321) Thin Wall. High pressure ducting, wall thickness or less. Weld bead controlled, X-ray.

Stock

Types OD WT Finish
Signal Slot Oval Pipes Size：40-110mm 1.0mm-2.0mm ; 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
Round Pipes 6mm-630mm 0.3mm-30mm 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
Square Pipes 8*8mm to 300*300mm 0.3mm-30mm 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
Rectangular Pipes 10*20mm~100*200mm 0.3mm-30mm 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
Oval Pipes Sizes ：4mm (short distance) ~ 270mm (Long Distance) 1.0mm -3.0mm 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
Single Slot Pipes 38.1-76.2mm 1.0mm-2.0mm 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
Capillary Pipes OD: 0.28mm -10mm 0.08mm – 1.2mm 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
Heat Exchange Pipes - ASTM A249 Seamless Pipe: 12.7～76.2 x 0.5～6.35mm
Welding Pipe: 12.7～76.2 x 0.5～3.175mm		 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
Arched Shaped Pipes 15*22—35*75 1.0—1.8 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
Double Slot Square Pipes Slot Width and Length: 10mm -30mm 1.0mm-2.0mm ; 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
thin-wall ASTM A270 22mm-108mm 0.7-2.0 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
Triangle Pipes Side Length: 16mm – 85mm 0.5mm-3.0mm 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
Hexagonal Pipes Side Length: 13mm – 85mm 0.5mm-1.8mm 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
Signal Slot Rectangular Pipes Slot Width and Height: 10mm- 30mm 1.0mm-2.0mm ; 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
Flat Oval Pipes 2.3*10.3—63*175 1.0—1.8 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
Fan Shaped Pipes 11*10*R15—80*80*R50 1.0—1.8 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
Seamless Pipes Size: 6mm – 430mm 0.8mm – 30mm 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
Inner polished Size ：12.5mm – 203.2mm 1.0mm – 5mm 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
Double Slot Round Pipes 38.1-76.2mm 1.0mm-2.0mm 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc
General equipment – ASTM A269 WD ：0.5mm-30mm OD ：10mm-300mm 2B,400#Bright, Brushed
(180#,220#,240#,320#400#,600#), Hairline, 8K Mirror, etc

Stainless Steel Pipe Sizes

Wall Sizes ( O.D.)
.010 1/16" , 1/8" , 3/16"
.020 1/16" , 1/8" , 3/16" , 1/4" , 5/16" , 3/8"
.012 1/8"
.016 1/8" , 3/16"
.028 1/8" , 3/16" , 1/4" , 5/16" , 3/8" , 1/2" , 3/4" , 1" , 1 1/2" , 2"
.035 1/8" , 3/16" , 1/4" , 5/16" , 3/8" , 7/16" , 1/2" , 16" , 5/8" , 3/4" , 7/8" , 1" , 1 1/4" , 1 1/2" , 1 5/8" , 2" , 2 1/4"
.049 3/16" , 1/4" , 5/16" , 3/8" , 1/2" , 16" , 5/8" , 3/4" , 7/8" , 1" , 1 1/8" , 1 1/4" , 1 1/2" , 1 5/8" , 2" , 2 1/4"
.065 1/4" , 5/16" , 3/8" , 1/2" , 16" , 5/8" , 3/4" , 7/8" , 1" , 1 1/4" , 1 1/2" , 1 5/8" , 1 3/4" , 2" , 2 1/2" , 3"
.083 1/4" , 3/8" , 1/2" , 5/8" , 3/4" , 7/8" , 1" , 1 1/4" , 1 1/2" , 1 5/8" , 1 7/8" , 2" , 2 1/2" ,3"
.095 1/2" , 5/8" , 1" , 1 1/4" , 1 1/2" , 2"
.109 1/2" , 3/4" , 1" , 1 1/4" , 1 1/2" , 2"
.120 1/2" , 5/8" , 3/4" , 7/8" , 1" , 1 1/4" , 1 1/2" , 2" , 2 1/4" , 2 1/2" , 3"
.125 3/4" , 1" , 1 1/4" , 1 1/2" , 2" , 3" , 3 1/4"
.134 1"
.250 3"
.375 3 1/2"

Stainless Steel Pipe Pressure Rating

Ratings for standard seamless stainless steel pipes, temperatures ranging 100°F to 750°F. All ratings in psig based on ANSI/ASME B 31.1.

`
SS Pipe Pressure Rating (psig)
SS Pipe Size(inches) SS Pipe Schedule Temperature(F)
100 200 300 400 500 600 650 700 750
1" 40 3048 2629 2362 2171 2019 1924 1867 1824 1810
80 4213 3634 3265 3002 2791 2659 2580 2528 2501
160 6140 5296 4759 4375 4068 3876 3761 3684 3646
1 1/2" 40 2257 1947 1750 1608 1496 1425 1383 1354 1340
80 3182 2744 2466 2267 2108 2009 1949 1909 1889
1604619 3984 3580 3291 3060 2916 2829 2772 2743
2" 40 1902 1640 1474 1355 1260 1201 1165 1141 1129
80 2747 2369 2129 1957 1820 1734 1682 1648 1631
160 4499 3880 3486 3205 2980 2840 2755 2699 2671
3" 40 1806 1558 1400 1287 1196 1140 1106 1084 1072
80 2553 2202 1979 1819 1691 1612 1564 1532 1516
160 3840 3312 2976 2736 2544 2424 2352 2304 2280
4" 40 1531 1321 1187 1091 1014 967 938 919 909
80 2213 1909 1715 1577 1466 1397 1355 1328 1314
160 3601 3106 2791 2566 2386 2273 2206 2161 2138
5" 40 1342 1158 1040 956 889 847 822 805 797
80 1981 1709 1535 1411 1312 1250 1213 1189 1176
160 3414 2945 2646 2433 2262 2155 2091 2049 2027
6 40 1219 1052 945 869 808 770 747 732 724
80 1913 1650 1483 1363 1267 1208 1172 1148 1136
160 3289 2836 2549 2343 2179 2076 2014 1973 1953
8" 40 1073 926 832 765 711 678 657 644 637
80 1692 1459 1311 1205 1121 1068 1036 1015 1005
160 3175 2738 2460 2262 2103 2004 1944 1905 1885
10" 40 974 840 755 694 645 615 596 584 578
80 1609 1388 1247 1147 1066 1016 986 966 56
160 3147 2714 2439 2242 2085 1986 1927 1880 1868

1 psi (lb/in2) = 6,894.8 Pa (N/m2) = 6.895x10-2 bar